Other

- Clamps to a threadless steerer, offers up to 3-1/4" stem height increase - Forged 6061 aluminum - Threaded alloy top cap

The tool-free Maxle Ultimate Front brings exceptional stiffness and durability to your ride in a high clamping force, easiest-to-use internal cam thru-axle system.

The Problem Solvers Handlebar Clamp Shim allows you to fit almost any handlebars in almost any stem. It's machined of light and durable aluminum and grooved on the inside to hold tightly.

Vuka Alumina Clip Risers are designed for use with the Vuka Alumina Clip's above-bar option. The risers are designed to offer a wider range of adjustability within the Vuka Alumina aero-cockpit system.

Surly wants you to be able to set up you ride just the way you want it. This pair of adapter washers make it so you can throw your favorite 135, 170, or 190mm O.L.D. 10mm solid axle hub into the rear end of a 142, 177, or 197mm spaced thru-axle frame. Add the adapters, add the wheel, install and tighten the nuts and, bam, you're ready to rip. Make sure the solid axle on your wheel is the right length for the frame spacing. For instance: 190mm OLD QR goes with 197mm thru-axle spacing.

- Powermeter Crank Arm Bolt Kit and AXS Cover Plug Drive Side M18/M30 Dub Steel Black Rival D1

The tool-free Maxle Lite brings exceptional stiffness and durability to your fork in a light, easiest-to-use expanding wedge thru-axle system. - Thread Length: 9mm - Thread Pitch: 15 x 1.5mm

RockShox's Maxle Lite is a lightweight aluminum through-axle system. It lets you remove and install your wheel as fast as with a standard quick-release while delivering the awesome stiffness with the improved strength and control of a through-axle. Plus, the lever can be closed in whatever position you like and no tools are required for installation and use!

- Allows quick chain removal without tools - MissingLink 410HD|~|1sp|~|BMX Heavy Duty chain|~|9.4mm|~|each|~| - MissingLink 410|~|1sp|~|BMX|~|8.6mm|~|each|~| - MissingLink II|~|8sp|~|all|~|7.1mm|~|6/card|~| - MissingLink-9|~|9sp|~|all|~|6.6mm|~|6/card|~| - MissingLink-10R|~|10sp|~|KMC, Shimano, SRAM|~|5.9mm|~|6/card|~| - MissingLink-10CR|~|10sp|~|Campagnolo only|~|5.9mm|~|6/card|~| - MissingLink-11|~|11sp|~|Campy, KMC, Shimano|~|5.5mm|~|6/card|~|

Replacement foam pads for Giant Contact clip-on aerobar clamps

- Compatible with Shimano, SRAM, Campagnolo and KMC 11 speed chains - DLC Coated - Non-reusable - Opening Tool Required - Card of 2 pairs

In the race against the clock, Bontrager's Race Lite Clip-On Aerobars S-Bend give you the advantage you need. Adjustable arm rests and extensions allow you to dial in your profile position so you can comfortably stay in a wind-slicing tuck. And the internal cable routing keeps everything out of the wind, nice and neat.

ReMatch adapters are designed to integrate different generations of Shimano Brakes to Shimano Shifters. Rematch Adapter 1.1 connects Shimano I-Spec A/B shifter to I-Spec II brake. - Made from CNC Machined T6061 Aluminum - Anodized Black - No additional hardware needed ReMatch 1.1 is NOT compatible with Deore M610 or SLX M670 shifters

A well-exercised dog is a happy dog, so give Fido a good workout while you ride! Sunlite's Dog Leash consists of a metal bar that mounts under the rear axle bolt or quick-release and straps to your chainstay. This keeps the center of gravity low so you stay stable if your dog pulls to one side. The bar is long enough to keep your pup away from the bike, too.

The Problem Solvers Quick-Release Nut Light Mount is an ingenious solution when your handlebars are too crowded to accept a light. This fine CNC-machined aluminum post simply screws on in place of your left, front quick-release nut to provide a great place to mount your light. Lower light mounting improves your depth perception and shows more details of the road condition ahead, too.

Giant's Connect SL S-Bend Carbon Aerobar Extensions are for use with Giant's Clip-On Aerobar Clamps (sold separately). This model features the S-Bend. Thanks to carbon construction, these are featherweight and super-stiff extension bars. Plus, they have 70mm of fore/aft adjustment to dial in your ideal aero position.

Rated fully KICKASS by a very authoritative entity who will remain unnamed, Surly's cast and polished stainless steel clamps won't rust or chip paint because they can't (even the black ones!). They're shiny! They look good! And most importantly, they deliver the clampability seatposts crave.

Problem Solvers Deckster pedal adapters. Converts SPD-compatible pedals to platform pedals for casual cruising. • Works with 2-bolt, SPD-style cleats, such as Time, Shimano, Crank Brothers, Wellgo and others. Not compatible with Speedplay • Cleats not included • 85 x 95 x 10mm platform • Hardware included, cleats not included

- Dust-proof and waterproof rubber seal cover. - Protect the power source connection on the frame when the e-bike is parked outside or when you carry it without the EnergyPak.

Thin, durable clear chainstay protector with extra-strong adhesive. - Overall length - 10.375

- Grade 10 chromium steel balls

Pro Compressionless brake housing eliminates flex from cable actuated braking systems, increasing power and improving lever feel. - KEB-SL - linear strand, Kevlar reinforced, compressionless brake housing with Slick-Lube liner - Perfect for full-housing, high-performance bikes with mechanical disc or rim brakes - 20 black alloy lined end caps, 10 black POP end caps included

Zipp developed an extensive line of aluminum aerobar extensions to provide the perfect fit for any rider, regardless of size or riding position. Vuka extensions are designed to deliver improved aerodynamics by placing hands closer together and nearer to the rider’s head to start airflow over the rider sooner. Designed with input from top bike fitters, the shape of the Vuka Alumina Evo is crafted to feel as if the rider is shaking hands with the bar. This is achieved through the use of a multi-radius bend paired with a 20mm inward roll of the bar that can be adjusted to dial in fit and achieve an ideal position. - Clean internal cable routing for easy installation - Length: 360mm

MTB fork seals are a vital protective part of the overall front suspension system, with a crucial impact on riding comfort and trouble-free operation in the harshest environments. This completely redesigned fork seal — adding on to SKF’s well established fork seals range that has already been available on the market for more than 10 years — consists of newly developed rubber compounds and new geometries for both the scraper lip and the sealing lip. The co-molded combination of compounds, together with improved sealing lip properties, offers enhanced followability on the shaft. In addition, there is a new metal insert and an open wound spring on the dirt scraper lip, effectively preventing the ingress of contaminants. - Extended sealing capability - Improved contamination exclusion - Reliable protection of the interior fork mechanism - Minimum friction for enhanced control

MTB fork seals are a vital protective part of the overall front suspension system, with a crucial impact on riding comfort and trouble-free operation in the harshest environments. This completely redesigned fork seal — adding on to SKF’s well established fork seals range that has already been available on the market for more than 10 years — consists of newly developed rubber compounds and new geometries for both the scraper lip and the sealing lip. The co-molded combination of compounds, together with improved sealing lip properties, offers enhanced followability on the shaft. In addition, there is a new metal insert and an open wound spring on the dirt scraper lip, effectively preventing the ingress of contaminants. - Extended sealing capability - Improved contamination exclusion - Reliable protection of the interior fork mechanism - Minimum friction for enhanced control

Mylar-laced woven elastic guard stretches around your fork to block mud/water as you ride.

RaceFace Aeffect R Dropper Post Small Parts.

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 26mm - Width: 5mm

Service your suspension fork with Enduro Seal KIts. - Custom made for each make and model of fork

Vendor Part # FK-6665

Disc brake adaptors designed to mate Magura disc brakes with a variety of frame mounts and rotor sizes. - Includes hardware to mount adaptor to frame

The all new Crank Brothers Highline remote kit. - Universal mounting system: top/bottom & left/right - Single bolt hinge locking system - Infinite spherical adjustment - Compatible with: Highline and other cable-actuated dropper seatposts

Attach these lightweight brackets to your water bottle bosses to serve as anchors for your cargo straps to carry just about anything, from sleeping pads to Nalgene bottles to barbeque sauce. These are a great addition to any bikepacking or touring cyclist’s on-bike storage toolkit. And their low profile means they don’t mess up the looks of your bike build while not in use.

Campagnolo Pulley Assemblies

Desgined to increase the stiffness of the EPS front derailleur on frames with flexible braze-on mounts, especially frames with carbon fiber mounts. - Required for use on carbon frames with carbon front derailluer braze on mounts

Campagnolo EKAR disc brake adapters. - Includes bolts

- Campagnolo Chain Links and Pins - 4 chain links and 2 connection pins - For Campagnolo 10 speed Ultra Narrow chains - Width: 5.9 - Drivetrain Speeds: 10

Sport brake housing packs high performance features into a colorful and durable package, making it a functional and aesthetic upgrade. - Slick-Lube lined housing reduces friction for faster cable movement and better braking response - High carbon internal steel coil for improved stiffness - Appropriate for Teflon coated cables as well as steel and galvanized - Length: 10m

New friction-reducing DebonAir air spring delivers the most responsive forks in RockShox history, maintaining traction in more conditions than ever before. - Allows for travel change on any 2019+ BoXXer fork

Saddle rail clamp outer-pieces to adapt Ritchey WCS Carbon 1-bolt posts to various saddle rail dimensions. - To retrofit WCS 1-Bolt carbon seatpost - Material: 7050 alloy

Clamp allows use of a braze-on derailleur on frames without the braze-on tab. Includes a tab to use SRAM's lightweight and easy-to-adjust chain control device. - Fits all SRAM road braze-on front derailleurs - ChainSpotter not included

Flat Mount Disc Caliper Bracket Bolts

Replacement faceplate for Ritchey WCS Trail stems.

Designed for legacy Shimano STI shifting systems, the Ritchey Cable Barrel Adjuster allows you to dial in your shifting with ease and precision. - Cable Tension Barrel Adjusters - STI compatible - Adjust the cable tension for optimal STI shifting

These are the correct connecting links for SRAM's 12-speed Eagle chains. They are great for installing new chains and fixing chains on the road and trail, too. They come in a four pack, for use with four chains.

Spindle spacers and kits allow BB30 cranks to be used in a variety of BB shells. - Use this kit to install these SRAM and Quarq BB30 road cranks in BB386 frames: Force 22, S900, S950, Red power meter, DZero Carbon, DFour, Elsa, Riken

Original equipment ceramic bearing pulleys for SRAM rear derailleurs. - Chain Compatibility: SRAM XX1

Authentic Ritchey hub conversion kit for mountain bike hubs. Hub Conversion Kit For MTN Hubs—TA 142x12 to QR

- Rear Derailleur GX 1X11 B Bolt and Limit Screw Kit

SRAM PressFit 30/English Bottom Bracket Adaptor allows conventional threaded bottom brackets to be installed in a PF30 frame. - Not to be used with internal threaded bottom brackets; compatible with BBs that use two external cups

Useful on some bikes with 135mm rear dropout spacing that have cranks with longer spindles.

Red eTap battery terminal cover

Replacement hoods for SRAM hydraulic shifter/brake levers.

This magnetic stem cap is designed exclusively for the unique shape of the revolutionary Ritchey Chicane stem. - Material: alloy - Fits only Chicane stem - Weight: 6g

X01 Eagle Cable Anchor Kit

Fit Kit SET811 contains all the parts needed to thru-axle mount an Old Man Mountain bike rack to the rear of your bike with a 12mm rear thru-axle. This kit includes: - 12 x 168—180mm thru axle with 1.75 mm thread pitch - A pair of pucks - Clear protective tape - Stainless steel mounting hardware - Axle mounting increases our rack's load capacity to 70lbs/33kg - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles. Axle Length does NOT equal hub standard. This refers to the length of the axle shaft. All axles are compatible with +/- 2mm.

The AXS battery cover is a light-weight cowling designed to protect the battery while installed on the derailleur. The AXS Battery Cover fits all AXS mountain bike derailleurs.

Replacement lever blades for various models of SRAM brake levers.

Fit Kit SET702 contains all the parts needed to thru axle mount an Old Man Mountain bike rack to your fork with a 15 mm thru axle. This kit includes: - 15 x 145 mm thru axle with M14 x 1.5 mm thread pitch to fit Fox 15 x 100 mm forks (may fit others as well) - A pair of pucks - Clear protective tape - Stainless steel mounting hardware - Axle mounting increases our rack's load capacity to 70lbs/33kg - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles. Axle Length does NOT equal hub standard. This refers to the length of the axle shaft. All axles are compatible with +/- 2mm.

REAR DERAILLEUR CAGE ASSEMBLY KIT RED XPLR AXS (FULL REPLACEMENT CAGE ASSEMBLY INCLUDING OUTER AND INNER CAGES, DAMPER AND PULLEYS) Use only SRAM parts with SRAM components. Installation of parts and accessories not originally intended could result in less than optimal performance and/or injury. For in-depth service information on SRAM products, refer to our website at www.sram.com/service. Information contained on SRAM Connect is subject to change at any time without prior notice.